Festo DADM-TK-... Монтаж - Handbuch (Seite 2)

Montageanleitung (de)
735 782 / 2008-05b
†‡
Toggle motion kit
DADM-TK-… Festo AG & Co. KG
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
The toggle motion kit is intended for converting the rotary indexing table
DHTG to toggle motion.
1. Parts list
11377d_1
1 Shock absorber (1x)
YSRD-...
2 Retaining ring (1x)
DIN 472
3 Seal (4x)
2. Preparing for assembly/disassembly
• Make sure that the rotary indexing table DHTG is unlocked:
This is the case when the rotating plate can be turned freely.
For unlock it:
• Pressurize compressed air connection A with min. 4 bar.
Warning
Danger of injury due to uncontrolled movements of the rotary indexing
table. Before assembly or disassembly:
• Exhaust the device and the system.
Note
During toggle motion the locking is separated by the rotary movement.
• Make sure that control of the locking/unlocking and the rotary
movement right/left is managed by your controller.
• Before commissioning the rotary indexing table DHTG, consult the
operating instructions ( !“Fitting the pneumatic components“).
3. Assembly
11377d_6
• Remove the stop plate 4.
• Unscrew and remove the
screws 5.
11377d_7
• Remove the two centre
O-rings 6.
11377d_8
• Place two seals 3 in the free
position.
11377d_9
• Fasten the stop plate 4.
• Tighten screws 5. Maintain
the permitted tightening
torque (
!Section 4).
11377d_2
• Unscrew the restrictor 8
and the screws 9.
• Remove the sub-base 7
with the fitted air connection
threads.
11377d_3
• Remove the two centre
O-rings aJ.
• Place two seals 3 in the free
position.
• Turn the rotating plate until
the left-hand drive piston
comes to the front
1).
11377d_4
• Push the shock absorber 1
into the drive piston.
• Fasten the shock
absorber 1 with the
retaining ring 2 in the drive
piston
1) .
11377d_5
• Fasten the sub-base 7 2) .
• Tighten the screws 9 and
the restrictor 8. Maintain
the permitted tightening
torque (
!Section 4).
11377d_10
• Remove the plugs (C)
and (D).
4. Screw sizes and tightening torque M
A
3)
DADM-TK- 65 90 140 220
5 Screw M4x16 (3x) M5x16 (5x) M6x16 (5x) M6x20 (5x)
[Nm] 1.5 2.9 5.9
8 Restrictor GRLA-M5-B GRLA-1/8-QS-8-D
[Nm] 1.5 5.5
9 Screw M4x16 (4x) M4x16 (6x) M6x16 (6x) M6x25 (6x)
[Nm] 2.9 9.9
1 )
With division into more than 2 parts (BG65 und 90)/ more than 3 parts (BG140 und 220):
There is a selector bolt in front of the left-hand drive piston which must be removed or
reinserted for conversion
.
2)
With division into more than 2 parts:
When fastening the sub-base make sure that the small compression spring fits into the
hole (X) again and presses against the selector bolt.
3)
Tolerance at M
A
> 1 Nm: ± 20%
1
2
3
8
aJ
1 2
4
5
6
3
4
D
C
5
9
7
3
7
8
9
X 2)