Metrohm 799 GPT Titrino - Handbuch (Seite 128)

3.2. Remote control commands
799 GPT Titrino
124
*Parameter Tree part "Parameters for DOS"
├ . DosPara Dosing parameters
│ ├ .Type Type of dosing volume, time, rate 3.2.2.52.
│ ├ .Volume Volume dosing
│ │ ├ .Volume Volume 0...10...99 999.99 ditto
│ │ ├ .DisType Second dosing criterion time, rate ditto
│ │ ├ .Rate Rate 0.001...150, max. ditto
│ │ ├ .Time Dosing time 1...100...999 999 ditto
│ ├ .Time Time dosing
│ │ ├ .Time Dosing time 1...100...999 999 ditto
│ │ ├ .DisType Second dosing criterion volume, rate ditto
│ │ ├ .Rate Rate 0.001...150, max. ditto
│ │ ├ .Volume Volume 0...10...99 999.99 ditto
│ ├ .Rate Rate dosing
│ │ ├ .Rate Rate 0.001...150, max. ditto
│ │ ├ .StopType Second dosing criterion volume, time ditto
│ │ ├ .Time Dosing time 1...100...999 999 ditto
│ │ ├ .Volume Volume 0...10...99 999.99 ditto
│ ├ .Pause Waiting time after start volume 0...999 999 3.2.2.53.
│ ├ .TDelta Time interv.for meas.acquisition 1...10...999 999 3.2.2.54.
│ ├ .DosUnit Selection of the dosing unit internal D0, external D1,
│ │ external D2 3.2.2.17.
│ ├ .Temp Titration temperature -170.0...25.0...500.0 3.2.2.55.
│ │
├ . StopCond Stop conditions
│ ├ .VStop Stop volume
│ │ ├ .Type Type of stop volume abs., rel., OFF 3.2.2.20.
│ │ ├ .V Volume for absolute stop volume 0...99.99...9999.99 ditto
│ │ ├ .Factor Factor for relative stop volume 0...±999 999 ditto
│ ├ .FillRate Filling rate 0.01...150.0, max. 3.2.2.23.
│ │
├ . Statistics Statistics
│ ├ .Status Status of statistics calculation ON, OFF 3.2.2.24.
│ ├ .MeanN No.of individual determinations 2...20 ditto
│ ├ .ResTab Result table
│ │ ├ .Select original,delete n,delete all ditto
│ │ ├ .DelN Deletion of individual results 1...20 ditto
│ │
├ . Monitoring Monitoring
│ ├ .MeasVal Monitoring of measured values
│ │ ├ .MeasMode Measured value pH, U, Ipol, Upol, OFF 3.2.2.56.
│ │ ├ .MeasInput Measuring input 1, 2, diff. ditto
│ │ ├ .PCurrent Polarization current 0...1...±127 ditto
│ │ ├ .PVoltage Polarization voltage 0...400...±1270 ditto
│ │ ├ .PolElectrTest Test for polarized electrodes ON, OFF ditto
│ │ ├ .pH Limits for monitoring of pH values
│ │ │ ├ .LowLim Lower limit -20.00...20.00 ditto
│ │ │ ├ .UpLim Upper limit -20.00...20.00 ditto
│ │ ├ .U Limits for monitoring of U values
│ │ │ ├ .LowLim Lower limit -2000...2000 ditto
│ │ │ ├ .UpLim Upper limit -2000...2000 ditto
│ │ ├ .Ipol Limits for monitoring of Ipol values
│ │ │ : as for U
│ │ ├ .U Limits for monitoring of Upol values
│ │ │ : as above
│ │ ├ .Action Action if out of limits end, hold, wait, none ditto